Common Problems with Bifold Doors

Common Problems with Bifold Doors

There are several simple problems which a bifold door can develop over time as it is subject to considerable use. Most of these problems are easy to identify and, once identified, can be solved by the property owner himself.

Panels Dragging on the Track

Dirt, sand, and other debris can fall into the track of the bifold door panels and get between the rollers. Vacuuming the track with a thin nozzle and then brushing it with a stiff brush will clear this out. It is a good idea to do this every few months or so, especially if the doors open to the outside, such as onto a garden or patio.

Doors Sagging Out of Alignment

After a year or so you may find that your bifold panels start to go out of alignment. This means that when you close your bifold door the panels won’t close perfectly flat or the top of the panels may not align. This type of problem is almost always a problem with the hinges or the height of the rollers and can often be simply adjusted. Most hinges have an adjustment screw that can be turned to raise or lower a particular panel. This is usually done by a slow quarter turn at a time until the desired alignment is achieved.

Stiff Handles and Locking Points

These areas tend to get dry and need to be lubricated from time to time. Make sure to use light machine oil or dedicated door lubricator and allow it to work for a minute or so before using. It’s tempting to use thick grease but it will only attract dirt and make the problem worse over time.

Draughts and Water at the Threshold

If you get a cold draught along the bottom of your bifold doors or you notice that water is entering your home during heavy rain then the problem could be due to failure of the compression seals. The compression seals are the rubber seals that compress onto the door frame when the bifold doors are shut. They can deteriorate, compress down or even come out of their track. Also make sure that the drainage slots in the threshold are not blocked with debris such as leaves. If water cannot get out of the drainage slots then it will enter your home instead.

Misting Between the Panes

Black-framed bifold door panels folding together, showing the hinges and handle where problems often develop

Condensation inside bifold doors is normal and can be simply wiped off. However, misting between the two panes of glass within a bifold door panel is a different issue altogether. This type of issue is often down to a failed seal around the edge of a double glazed unit and cleaning will not clear this type of moisture. These units would then need to be replaced as a whole.

Worn Hinges and Rollers

A clicking, grinding or squeaking sound could indicate a problem with a hinge or roller. Give all the hinge pins and roller wheels a good clean with a tough brush and then apply some light lubricant. Repeated movement can cause wear and tear to the metal parts, causing them to develop pitting or wear. Such parts can be replaced individually.

Multi-Point Locks That Won’t Throw

A door that doesn’t lock fully may seem like a mere annoyance but can, depending on the nature of the multi-point lock fitted, become a security problem as well as an inconvenience. If your bifold door doesn’t lock fully then check the door against the recognised security accreditation for that product. The cause will usually be found to be that the frame has dropped slightly and the hinges and/or keeps will need to be realigned. Depending on the type fitted this may be a simple job but it is always better to get someone who knows what they are doing to check the door and make any necessary adjustments to ensure a proper and secure fit.

DIY Fix or Call a Fitter

Most bifold door problems are small mechanical problems which can be resolved quickly if found early. Hinges, and roller wheel surfaces can be cleaned and lubricated. Track dirt can be cleared with a brush or vacuum. Drainage slots at threshold ends can be cleared of leaves and dirt. If any of these parts wear, they can be replaced individually. However, sometimes a frame can droop and not be able to be adjusted back to square, or a glazed unit may fail or a locking point internally seize or be damaged.

A useful reference for Bifold Doors Cardiff is Choice Trade Frames.

Bifold door problems mostly consist of small mechanical problems that can be easily repaired if you find them in time.

Leave a Reply

Your email address will not be published. Required fields are marked *